Intake Valve Actuator Solenoid Test using Caterpillar ET Software
Intake Valve Actuator Solenoid Test using Caterpillar ET Software Intake Valve Actuator Solenoid Test (OnHighway Trucks) Purpose The Intake Valve Actuator Solenoid Test can be used to verify the operation of the Intake Valve Actuator Solenoid on one or all Cylinders. These tests provide a method for finding wiring or solenoid problems, and they are […]
Calibrate Throttle Position Sensor for Bobcat 5600
1. Description The drive system calibration procedure shows how to calibrate the drive system by following the service analyzer instructions displayed on the Service PC.The travel pedal and brake calibration procedures show how to calibrate the travel and brake pedals output ranges by following the service analyzer instructions displayed on the Service PC. 2. Bobcat […]
Accessing Parameter Lockout CAT ET Software
The Parameter Lockout function allows parameters to be locked so that they cannot be changed anywhere in the Service Tool by service Mechanics. To unlock the parameters, Factory or Customer Passwords are required. Accessing To run the Parameter Lockout function: 1). Connect CAT ET 2022A to the Service Tool connector. 2). Select Parameter Lockout from the Service Menu. 3). The Parameter […]
Data Monitor On Allison DOC Software
Allison DOC Software The Data Monitor allows you to view controller information in a table format. The data display is dynamic and displays real-time data as it occurs. This screen is divided into four major grids: Diagnostic Data (left side), Input Functions (upper right side), Output Functions (center right side), and Shift Inhibits (lower right […]
Programming ECM using CAT ET Software
The WinFlash tool can be used to set up and consecutively program the Flash memory of all onboard ECMs. Instructions To program an ECM: 1). Start a connection to the Service Tool. Read More: How to Connecting CAT ET Software to the ECM. Select one of the following ECMs…. Blank Box: #2841B017JJ Flash Required. Select Flash. 2). […]
PERKINS 1204F Troubleshooting
General Information PERKINS 1204F Troubleshooting Important Safety Information Do not perform any procedures in this Troubleshooting Guide until you have read the Operation and Maintenance Manual and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in […]
Tech Tool When ECU Programming Solution
Error 121 is a generic “failed to program” message, so this can have several causes. Tech Tool 2.8.130 Solution 1: One common cause is low battery Voltage to the ECU that is being programmed. Solution 2: Check all connections, and ensure that the vehicles batteries are good and fully charged. You can also remove power […]
Hitachi Hydraulic Excavtor ZX200-1 Service Manual
Factory Workshop Manual For Hitachi Zaxis Excavator. Manual Contains Illustrations, Instructions, Diagrams For Step By Step Remove And Install, Assembly And Disassembly, Service, Inspection, Repair, Troubleshooting, Tune-Ups Link: Hitachi Hydraulic Excavtor ZX200-1 Service Manual Pass: obdii GENERAL INFORMATION Precautions for Disassembling and Assembling Tightening Torque Painting -UPPERSTRUCTURE Cab Counterweight Main Frame Pump Device Control Valve […]
How to Use JCB ServiceMaster 4 Program Injector Code for JCB Machine
JCB ServiceMaster 4 2022.05 Procedures 1. Please make a note of the injector codes. These can be found on the fuel injector.The injector codes should be noted in cylinder order where cylinder 1 is closest to the FEAD belt and cylinder 4 closest to the flywheel. 2. Make sure the machine is switched on, immobiliser […]
How to remove Detroit ECM Password by DDCT
This instruction show you guide on how to use DDCT (Detroit Diesel Calibration Tool) for Detroit Diesel engine ECM. 1. Process Step 1: Run Detroit Diesel Calibration Tool (DDCT) as administrator Step 2: Go to comms and select upload calibration Step 3: The calibration will be loaded in the ddct, (properly routing the root metfiles) […]
