P0601 Internal Control Module Memory Check Sum Error D6CC
Component Location
P0601 Internal Control Module Memory Check Sum Error D6CC
General Description
The ECM judges whether vehicle condition is good or not through algorithm check-sum. All data of algorithm check-sum is composed of combination of “0” and “1”. The algorithm check-sum means that adds all values in the character row. The criteria to judge whether the ECM is good or not is sensed by comparing the stored values in the ECM and the obtained values through algorithm.
DTC Description
Item | Detecting Condition | Possible Cause | ||
DTC Strategy | • Voltage monitoring | • Defective ECM (internal memory) |
||
Enable
Conditions |
• Ignition ON or at driving | |||
Threshold
Value |
• MIL ON at IG ON |
|||
Diagnosis
Time |
• Above 1 seconds | |||
Fail Safe | Fuel Cut | Yes | • Stop engine (Impossible to start) |
|
Fuel Limit | No | |||
MIL | On |
Monitor Scantool Data
1.Self-diagnostic inspection
(1) IG “OFF”, and set the start safety switch ON.
(2) Connect scantool to the self-diagnosis connector.
(3) Turn the ignition to ON.
(4) Select vehicle model and system to diagnose and press ENTER.
(5) Is the communication possible between system and scan tool?
YES | Go to “System” procedure. |
NO |
Turn the ignition OFF. Disconnect scantool and repeat above step(step 1 to step 4) 2 or 3 times. If the same symptom occurs, proceed step below. |
Terminal & Connector Inspection
1. Many malfunctions in the electrical system are caused by poor harness and terminals. Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage.
2. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage.
3. Has a problem been found?
YES | Repair as necessary and then go to “Verification of Vehicle Repair” procedure. |
NO | Go to “Component Inspection” procedure. |
1.ECM Inspection
(1) IG “OFF”, and set the start safety switch ON.
(2) Remove the ECM.
(3) Visually check ECM for entry of water, burnt odor in internal circuit.
(4) Reinstall the ECM and perform diagnostic troubleshooting.
(5) Is the diagnostic troubleshooting normal?
YES | Go to “Verification of Vehicle Repair” procedure. |
NO | Replace the ECM and then go to “Verification of Vehicle Repair” procedure. |
In most cases, the ECM is not defective. Before replacing the ECM, check the poor connection of connector and communication cable. And check the in/out power condition of ECM.
Verification of Vehicle Repair
After a repair, it is essential to verify that the fault has been corrected.
1. Connect scantool and select “Diagnostic Trouble Codes(DTCs)” mode.
2. Using a scantool, clear the DTC.
3. Operate the vehicle within DTC enable conditions in General Information.
4.Are any DTCs present?
YES | Go to the applicable DTC procedure. |
NO | System is performing to specification at this time. |
Contact Us
★ Whatsapp: +84 858966333
★ Skype: vietvehicle@gmail.com
★ Wechat ID: Vietvehicle
★ Zalo: +84858966333
★ Email: Service@vietvehicle.com
★ Fanpage: https://www.facebook.com/Vietvehicle/
★ Website: https://vietvehicle.com/
★ Youtube chanel: VIETVehicle
Related Posts
- Intake Valve Actuator Solenoid Test using Caterpillar ET Software
- Injector Codes Calibration using CAT ET Software
- P0487 EGR Throttle Position Control Circuit (D6CC)
- GHG17 Heavy Duty Machine FIS Low Pressure Leak Test by DDDL
- P0341 Cam Synchronization Error D6CA
- Accessing Parameter Lockout on CAT ET Software
Branch
Hot Products
- ✔ NAVISTAR ENGINE DIAGNOSTICS 7.9.7 [2022.11]
- ✔ Scania Multi 2022 [2022.03] Spare Parts & Manuals
- ✔ Kubota Diagmaster 2022 Level 6
- ✔ Hino DX3 1.22.12 [2022.12]
- ✔ Bendix Acom Pro 2022 v3
- ✔ JPRO 2022v3
- ✔ Doosan DMS-5 3.0.1 2022
- ✔ HITACHI ALL IN ONE & MPDR 3.22
- ✔ NexIQ eTechnician 2.5
- ✔ Wabco Toolbox Plus v13.7
- ✔ Diamond Logic Builder 2022
- ✔ John Deere Service Advisor 5.3.210
- ✔ Eaton Service Ranger 4.11 [2022]
- ✔ Allison DOC® 2021.5
- ✔ E-IDSS 12.2021 [Diagnostic Isuzu Industrial Engines]
News
VIETVehicle.org
